Skyrc T6200 Charger Manuel d'utilisateur télécharger pdf (Page 4)

MAIN FEATURES

WARNING AND SAFETY NOTES

These warnings and safety notes are particularly important. Please

follow the instructions for maximum safety; otherwise the charger

and the battery can be damaged or at worst it can cause a fire.

The allowable DC input voltage is 11-18V DC.

Never leave the charger unattended when it is connected to its power supply. If any

malfunction is found, TERMINATE THE PROCESS AT ONCE and refer to the operation

manual.

Keep the charger well away from dust, damp, rain, heat, direct sunshine and vibration.

Never drop it.

This charger and the battery should be put on a heat-resistant, non-flammable and non-

conductive surface. Never place them on a car seat, carpet or similar surface. Keep all

flammable volatile materials away from the operating area.

Make sure you know the specifications of the battery to be charged or discharged to

ensure it meets the requirements of this charger. If the program is set up incorrectly, the

battery and charger may be damaged. Fire or explosion can occur due to overcharging.

This warranty is not valid for any damage or subsequent damage arising as a result of a

misuse or failure to observe the procedures outlined in this manual.

To avoid short circuiting between the charge lead, always connect the charge cable to the

charger first, then connect the battery. Reverse the sequence when disconnecting.

Never attempt to charge or discharge the following types of batteries:

A battery fitted with an integral charge circuit or a protection circuit

A battery pack which consists of different types of cells (including different manufacturers)

A battery that is already fully charged or just slightly discharged

Non-rechargeable batteries (pose an explosion hazard)

A faulty or damaged battery

Batteries installed in a device or which are electrically linked to other components

Batteries that are not expressly stated by the manufacturer to be suitable for the

currents the charger delivers during the charge process

Please bear in mind the following points before commencing charging:

Did you select the appropriate program suitable for the type of battery you are charging?

Did you set up adequate current for charging or discharging?

Have you checked the battery voltage? Lithium battery packs can be wired in parallel and

in series, i.e. a 2-cell pack can be 3.7V (in parallel) or 7.4V (in series).

Have you checked that all connections are firm and secure? Make sure there are no

intermittent contacts at any point in the circuit.

Be very careful to choose the correct voltage for different types of battery otherwise you may cause

damage to the batteries. Incorrect settings could cause the cells to fire or explode.

Standard Battery Parameters

LiPo LiIon LiFe

NiCd MiMH

3.7V/cell 3.6V/cell 3.3V/cell

1.2V/cell 1.2V/cell 2.0V/cell

4.2V/cell 4.1V/cell

3.6V/cell

1.5V/cell 1.5V/cell 2.46V/cell

3.7V/cell3.8V/cell 3.3V/cell

n/a n/a n/a

3.0-3.3V/cell 2.9-3.2V/cell 2.6-2.9V/cell 0.1-1.1V/cell 0.1-1.1V/cell

1.8V/cell

Nominal Voltage

Max Charge Voltage

Storage Voltage

Min. Discharge Voltage

T6200T6200

0504

WARNING AND SAFETY NOTES

Fire Hazard!WARNING

Re-Peak Mode of NiMH/NiCd Battery

In re-peak charge mode, the charger can peak charge the battery once, twice or three times in a row

automatically. This is good for making certain the battery is fully charged, and for checking how well

the battery receives fast charges.

Delta-peak Sensitivity for NiMH/NiCd

Delta-peak sensitivity for NiMH/NiCd battery: The automatic charge termination program based on

the principle of the delta-peak voltage detection. When the battery's voltage exceeds the threshold,

the process will be terminated automatically.

Automatic Charging Current Limit

You can set up the upper limit of the charging current when charging your NiMH or NiCd battery, it is

useful for the NiMH battery of low impedance and capacity in the 'AUTO' charging mode.

Capacity Limit

The charging capacity is always calculated as the charging current multiplied by time. If the charging

capacity exceeds the limit, the process will be terminated automatically when you set the maximum

value.

Temperature Threshold*

The battery's internal chemical reaction will cause the temperature of the battery to rise. If the

temperature limit is reached, the process will be terminated.

Processing Time Limit

You can also limit the maximum process time to avoid any possible defect

Motor RPM Tester

Users connect the sensor motor and charger with sensor wire, set the pulse width and test the RPM

of the motor.

Servo Tester

Connect the servo and the charger with wire, change the pulse width value and check whether the

servo works or not.

PC Control Software “Charge Master”

There is a mini USB port in the charger which can be used to connect it to the PC. You need optional

USB cable (USB A Male to Mini B Male) which is not included in the package. The free “Charge

Master” software gives you unparalleled ability to operate the charger through your computer. You

can monitor pack voltage, cell voltage and other data during the charging, view charge date in real-

time graphs. And you can initiate, control charging and update firmware from “Charge Master”.

When your charger is connected to computer, the “Charger Master” takes over the control of charger.

You can control and operate the charger via the “Charger Master” only.

Multi-Language and Four Color Theme Optional

There are two languages and four kinds of color theme stored in the charger and users could select

the display language and color theme as basing on personal preference.

Inner resistance of battery pack

Measure Inner resistance of battery pack inclusively all connectors and leads.

You can download Charge Master software from our website

www.skyrc.com

Users can control and monitor the charge through computer when Charge Master software is installed.

This function is available by connecting optional temper ture probe which is not included in the package.a

1 2 3 4 5 6 7 8 9 ... 13 14

Commentaires sur ces manuels

Pas de commentaire

Skyrc T6200 Charger Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Fournisseurs d'énergie Skyrc T6200 Charger